Making Your Own Plastic Molded Objects
Sulpho-Plastics
This plastic is particularly adaptable for making molds and light castings requiring tensile strength but very clear outline. It may also be used for making ornaments and novelties. However, as this is flammable, do not use for ashtrays.
While the name would convey the thought of plastic sulphur which is an unstable allotropic form of sulphur, this is not the case, as the sulphur acts as a bond to hold the filler together and forms a stable material.
Interesting marble effects may be obtained by varying the filler used; and by substituting a small quantity of chalk to replace some of the graphite, a very pleasing glazed surface marble is formed.
As long as the graphite is retained as a filler, this plastic may be electroplated and forms a very economical base for such work.
FORMULA: Mix thoroughly and smoothly together 25 parts of GRAPHITE and 75 parts SULPHUR and place over heat. As soon as the mass has melted and runs like water, remove from the heat. In any case, a temperature of 235 degrees F. not be exceeded. If heated about 250 degrees F. the plastic will form a rubbery mass and will have to be cooled and reheated. In this liquid state the plastic is ready for casting and may be poured into smooth surfaced molds.
N.B. to heat this mixture properly, a good even heat is necessary. Should the heating be done by flame, the container should be placed in a sand bath to insure an even heating surface. The cast-iron top of a heater or stove is excellent.
EQUIPMENT: The only equipment for the above that is required is space enough to work in, a stove or heater, a pan to heat the mixture in and a bench or table.
PROCEDURE: Before making any casting you will need a pattern. After choosing a design that fits your need, your next step is to make the mold. Then you may start into production. If your product requires any holes, threads or machining, this may be done in the same manner as in working with a metal casting.
Always think of your castings as metal, for they have metallic properties, i.e., conduct heat, electricity and can be electroplated. In fact, the most valuable quality of Sulpho-Plastic is the fact that it can be used as a metal substitute. This permits you to make products that look and are as good and even better, in some cases, than a true metal. For instance, to make a chrome plated metal lamp base or other metal casting would require foundry equipment and machine shop work and in all, a process miles out of the reach of the small manufacturer. However, with our plastic, a lamp base, similar in all respects, may be made for a fraction of the other cost.
ELECTROPLATING: While this can be done at home with very little equipment, it is advisable to have it done by a commercial electroplater, who does it very cheaply and much more efficiently. Electroplating is only used on expensive replicas and is not advisable for a start.
DESIGN: The number and variety of articles that can be manufactured from Sulpho-Plastic is practically unlimited and to make a complete list would be impossible. However, any article of reasonable size and simplicity of design such as lamps, curios, Buddhas, incense burners, elephants, vases, plaques, brooches, desk-sets, toys paper weights, etc., may be cast by using an original or purchased article for a pattern or model - or an original design may be patterned in clay and used to make a mold. It is advisable for the beginner to choose a simple article for a start, preferably solid, such as paper weights or book-ends.
MOLDS: Molds may be made of metal or plaster of Paris. Metal molds, however, require a great deal of skill and equipment to produce. Therefore for the beginner, it is advisable to use plaster of Paris.
To make plaster of Paris molds; first obtain a box, wood or cardboard will do; about an inch longer each way than the article to be cast. Coat the inside of the box very thoroughly, yet thinly, with stearine or sweet oil. Use this also on the article to be cast. This acts as a lubricant and the plaster of Paris will not cement itself to either the box or the article, if the oil is evenly distributed.
Now, next make a thick, creamy mixture of plaster of Paris by sifting the plaster gradually into the water, stirring constantly to prevent lumping. Let this stand a few minutes to allow the air bubbles to escape. Pour mixture slowly over pattern in this box to about double the thickness of the pattern.
Allow several hours to dry, then remove. If the stearine or sweet oil was applied properly, this will be easy. When the mold is thoroughly dry, give it a coat (thin) of shellac and repeat in 12 hours. Mold is now ready for use.
MOLDING: First and foremost always make sure that you have lubricated your mold with beeswax or stearine. Place molds on a reasonably level surface and pour the sulpho-plastic into the mold, quickly and smoothly. Do not pour from a height as this will break the lubricant and leaves blemishes on the casting. Plastic must be poured quickly to prevent cooling in folds and thus making a poor casting. One of the big assets of sulpho-plastics is the fact that it dries and hardens almost immediately. There is no long wait for casting to dry.
Related Articles
How to Make Lamps and Vases from Bottles
To do this you must place the glass under water completely, then with a pair of ordinary scissors, proceed to cut the glass as you would paper or cloth. This method is, of course, not as smooth as job as the methods described above.
Our Multipage Plastics Report
In order to prepare a foam of given density, thoroughly mix Polylite 8601 with the necessary amount of Catalyst R1 and water.
Jewelry From "Ordinary" Treasures
Almost everyone has a box of sparkling old buttons from Grandma's sewing chest to marvel at, or set of dominoes, checkers or mah-jongg pieces rescued from a flea market.
How to Cash in with Simple Formulas
You can copy any of these Formulas and sell to other Agents, or put them together in packages - under your own name - and sell to Agents.
Six Simple Plastics Formulas
This is the age of plastics! One of the most amazing developments in this age of wonders . . . NEW developments and discoveries are constantly being made in the plastic field. Here is a truly rich field for experimentation.
Flexible Mold Compound
This new mold material is much superior to ordinary gelatin (mold glue) and is very easily made. It does not shrink or dry out like ordinary casting gelatins.
Fishing Bait - 10 Oil-Based Formulas
Mix together 5 parts oil of rhodium and 2 parts oil of cumin.
Acid Test for Gold
If you wish to find out if a piece of jewelry is made of gold, touch it with a glass stopper which has been wetted with nitric acid.
Homemade Kentucky Beer (15 Gallons)
Use 15 gallon plastic garbage can with clip on lid. You need:
How You Can Color Fireplace Flames
If you enjoy sitting around your fireplace and watching colorful flames dance, you'll be happy to know you can color your own flames quite cheaply. Basically, there are three methods of coloring fireplace flames.